江蘇春晨電纜有限公司:http://www.gd5688.cn/st82365/
江蘇春晨電纜有限公司專業生產YFFB扁電纜,YFFB扁電纜適用于發電、冶金、化工、港口等惡劣環境移動電器設備之間電器連接,使用環境溫度：復合物-40℃～+70℃；聚氯乙烯-15℃～+70℃,
This specification refers to the preparation of "3952-2008 GB/T" standard for electrical purposes.
1 范圍,
1 range
This specification provides for the procurement requirements, test methods, inspection rules, packaging, marking, transportation and storage of copper wire for electrical purposes. Suitable diameter is 6 ~ 35.0mm, for further drawing wire or other electrical circular copper wire copper conductor.
2 引用標準
2 reference standards
下列標準均應為有效版本；
The following standards shall be the latest and valid version;
GB/T4909 《裸電線試驗方法》
GB/T4909 "bare wire test method"
GB/T3048 《電線電纜 金屬導體材料電阻率試驗方法》
GB/T3048 "test method for electrical resistivity of metallic conductor materials for electric wires and cables"
GB/T5121 《銅及銅合金化學分析方法》
GB/T5121 "copper and copper alloy chemical analysis method"
GB/T13293 《高純陰極銅化學分析方法》
Analysis of high purity copper cathode GB/T13293 "learning method"
3 要求
3 requirements
3.1銅線坯牌號、狀態、規格應符合表1的規定。
3.1 copper billet grades, status, specifications should comply with the provisions of table 1.
表 1 銅線坯牌號、狀態、規格
Table 1 copper wire blank grades, status and specifications
牌 號 狀 態 直 徑 mm
Grade state diameter mm
T1、T2 熱（R） 6.0～35.0
T1, T2 heat (R) 6 ~ 35
TU1、TU2 熱（R）
TU1, TU2 heat (R)
硬（Y） 6.0～12.0
Hard (Y) 6 ~ 12
3.2尺寸及其公差
3.2 dimensions and tolerances
3.2.1銅線坯的直徑及其允許偏差應符合表2 的規定。
The diameter of the 3.2.1 copper wire and the allowable deviation shall be in accordance with the provisions of Table 2.
表2 銅線坯的直徑及其允許偏差
Table 2 the diameter of the copper wire and the allowable deviation
標稱直徑mm 允許偏差mm 標稱直徑mm 允許偏差mm
Nominal diameter mm allowable deviation mm nominal diameter mm allowable deviation mm
6.0～6.35 +0.5
6 ~ 6.35 +0.5
-0.25 ＞12.0～19.0 ±0.5
-0.25 > 12 ~ 19 + 0.5
＞19.0～25.0 ±0.6
> 19 ~ 25 + 0.6
＞6.35～12.0 ±0.4 ＞25.0～35.0 ±0.8
> 6.35 ~ 12 + 0.4 > 25 ~ 35 + 0.8
3.2.2銅線坯應成卷供應，每卷應為連續一根，不允許焊接。
3.2.2 copper blanks should be supplied in rolls, each of which shall be a continuous one, and shall not be allowed to be welded.
3.3力學性能
3.3 mechanical properties
表3 銅線坯的力學性能
Table 3 Mechanical Properties of copper wire blank
牌號 狀態 直徑
Grade state diameter
mm 抗拉強度 N/mm2
Mm tensile strength N/mm2
不小于 伸長率 %
Not less than elongation%
不小于
Not less than
T1、TU1 R 6.0～35 — 40
TU1, R T1 6 ~ 35 - 40
T2、TU2 — 37
TU2, T2 - 37
TU1、TU2 Y 6.0～7.0 370 2.0
TU2, Y TU1 6 ~ 2 7.0370
＞7.0～8.0 345 2.2
> 7 ~ 2.2 ~ 8.0345
＞8.0～9.0 335 2.4
> 8 ~ 2.4 ~ 9.0335
＞9.0～10.0 325 2.8
> 9 ~ 2.8 ~ 10.0325
＞10.0～11.0 315 3.2
> 10 ~ 3.2 ~ 11.0315
＞11.0～12.0 290 3.6
> 11 ~ 3.6 ~ 12.0290
銅線坯的力學性能應符合表3的規定，硬態銅線坯充分退火后應滿足表3中相應牌號熱態產品的伸長率要求。
The mechanical properties of copper wire should be in accordance with the provisions of Table 3, the hard state copper billet should meet the requirements of the corresponding grades in Table 3 after full annealing.
3.4扭轉特性
3.4 torsion characteristics
。
The diameter of 6.0mm ~ 10.0mm (hot) T1, T2 grade copper wire should be carried out after torsion torsion test, there should not be ruffled and inclusion defects, bright metal skin does not crack as a criterion of unqualified products. The torsion properties of different grades of copper wire should be in accordance with the provisions of table 4.
表4 銅線坯扭轉性能
Table 4 torsion property of copper wire
牌號 狀態 正轉轉數 反轉至斷裂的轉數，不少于
The state is reverse to the speed grade fracture speed, not less than
T1、TU1 R 25 25
TU1, R T1 2525
T2、TU2 25 20
T2, TU2 2520
3.5電性能
3.5 electrical properties
3.5.1采用4.5.2條規定的試樣時，銅線坯的電阻率應符合表5的規定。
The resistivity of the copper wire should be in accordance with the provisions of table 5 when 3.5.1 is specified by 4.5.2.
表5 銅線坯的電阻率
Table 5 resistivity of copper wire
牌 號 狀 態 體積電阻率ρ20 Ω·mm2/m
The volume resistivity of state grade 20. Mm2/m.
不大于
Not more than
T1、TU1 R 0.01707
TU1, R T1 0.01707
T2、TU2 0.01724
T2, TU2 0.01724
TU1 Y 0.01750
Y TU1 0.01750
TU2 0.01777
TU2 0.01777
3.5.2采用4.5.3條規定的試樣時，銅線坯的電阻率應符合表4中相應牌號熱態產品的規定指標。
3.5.2 the resistivity of the copper wire should conform to the provisions of the corresponding grades in Table 4 when the 4.5.3 is used for the test.
3.6表面質量
3.6 surface quality
3.6.1銅線坯應圓整，尺寸均勻。
3.6.1 copper billet should be round, uniform size.
3.6.2銅線坯表面不應有皺邊、飛邊、裂紋、夾雜物及其他對使用有害的缺陷。
3.6.2 copper billet surface should not be ruffled, flash, cracks, inclusions and other defects on the use of hazardous.
4 試驗方法
4 test methods
4.1氧含量試驗
4.1 oxygen content test
The oxygen content of T1 TU1 and 4.1.1 grade copper wire is according to GB/T13293, and the oxygen content of T2, T3 and TU2 grades of copper wire is according to GB/T5121.
4.1.2氧含量的測定應符合表6的規定。
Determination of 4.1.2 oxygen content should be in accordance with the provisions of table 6.
表6 銅線坯的氧含量
Table 6 oxygen content of copper wire
牌 號 氧含量 %
Grade oxygen content%
不大于
Not more than
T1 0.045
T1 0.045
T2、T3 0.050
T2, T3 0.050
TU1、TU2 0.0010
TU1, TU2 0.0010
4.2尺寸測量方法
4.2 dimensional measurement method
銅線坯的尺寸測量方法按GB/T4909.2的規定進行。
The measurement method of the size of the copper wire is carried out according to the provisions of GB/T4909.2.
4.3力學性能檢驗方法
4.3 mechanical property test method
銅線坯的室溫拉伸試驗按GB/T4909.3的規定進行。
The room temperature tensile test of copper wire blank is carried out according to the provisions of GB/T4909.3.
4.4扭轉試驗方法
4.4 torsion test method
4.4.1扭轉試驗按GB/T4909.4的規定進行。
4.4.1 torsion test according to the provisions of GB/T4909.4.
4.4.2 samples should be taken from 3.6.1 and 3.6.2 to check the qualified copper wire. The original gauge length is 300mm, reverse speed should not exceed 30r/min; samples around the axis of rotation specified in Table 4 is transferred, and then transferred to the reverse fault.
4.5電性能檢驗方法
4.5 electrical performance test methods
4.5.1銅線坯電阻率測試方法按GB/T3048.2的規定進行。
The resistivity test method of 4.5.1 copper wire blank is carried out according to the regulations of GB/T3048.2.
4.5.2電阻率試驗可在經酸洗但未經進一步加工和退火的銅線坯試樣上直接進行。
4.5.2 resistivity test can be carried out directly on the sample of copper wire, which has been processed by pickling without further processing and annealing.
4.5.3 resistivity test can also be prepared according to the following methods: samples were determined by acid and sample processing to the diameter of 2mm to oil, by 500 to 550 DEG C protective atmosphere annealing in 30min, then in the same atmosphere quickly transferred to the cooling water.
4.6表面質量檢查方法
4.6 surface quality inspection method
銅線坯的表面質量用目視檢查。
Visual inspection of surface quality of copper wire.
5 檢驗規則
5 inspection rules
5.1檢驗方法及要求
5.1 inspection methods and requirements
。
5.1.1 each batch of incoming wire billet according to GB/T3952-2008 standard requirements for sampling inspection, the same specifications, the same time as the production of a batch (less than 60T), and the complete package, with product certificate.
5.1.2 each batch of sampling inspection items according to the provisions of GB/T3952-2008, size deviation, tensile strength, elongation, resistivity, torsion, appearance and other inspection.
5.1.3 each batch of 30T and the following to take no less than 1 samples, 30 ~ 50T should be no less than 2 samples, 60T and above to take not less than 3 samples. Electrical performance is not qualified, the batch of substandard. Tensile strength, elongation, torsion, surface quality, size deviation is not qualified, that should be checked by volume, according to volume determination.
5.1.4對報檢的每批銅線坯必須附有供方材料的質保書或檢測報告。
A warranty or inspection report for each batch of copper wire 5.1.4 for inspection and quarantine must be accompanied by a supplier of materials.
5.2檢測項目
5.2 test items
5.2.1可檢項目為尺寸、外觀、伸長率和電阻率。
5.2.1 inspection items for size, appearance, elongation and electrical resistivity.
5.2.2對于無法檢測的性能依據生產廠商檢測報告或質保書驗收，必要時作委外試驗。
5.2.2 for the inability to detect the performance based on the manufacturer's test report or quality assurance book acceptance, if necessary, the Commission test.
6試驗規定
6 test regulations
6.1 試樣檢測后按要求做好原始記錄，并填寫記錄表格。
6.1 after testing, according to the requirements of the original record, and fill in the record form.
6.2 依據標準要求和本
6.2 according to the standard requirements and the
