ZY6112豎井管道垂直燃燒試驗機
Shaft pipe vertical burning test machine

UL 1666豎井管道垂直燃燒試驗機是目前zui為熱門的產品，同時也是我司zui為優勢的產打產品之一，曾與四川消防研究院、中國標準化研究院等七千多家省市質檢院是我們的合作客戶。
UL 1666 vertical shaft pipeline burning machine is currently the most popular products, at the same time also is one of our most advantage products within the play, with sichuan fire research institute, China academy of standardization is more than seven thousand cities and provinces such as quality inspection institute cooperation of our customers.

一．適用范圍：Scope of application:
適用于樓與樓層間管道內配線及升降機用電纜燃燒性能的評定。
Suitable for floor and floor wiring between the pipe and elevator with cable combustion performance evaluation.
 
二．符合標準：Conform to the standard:
符合UL1666<<Test for flame propagation height of electrical and optical-fiber cables installed vertically in shafts>>試驗標準
Meet UL1666 < < Test for flame propagation height of electrical and optical - fiber cables installed vertically in shafts > > Test standard

三．主要參數：The main parameters:
3.1 試驗箱
  3.1.1 U型壓力計：測量試驗箱的壓力維持在0-12PA
  3.1.2 溫濕度計：測量試驗箱的溫度和濕度
  3.1.3試驗箱的結構：整體結構由混泥土墻面砌成，*層為1.22M,第二層為3.66M,頂層為2.24M. 外部尺寸：7.12M高x1.3M寬x2.5M長。
  3.1.4墻面結構是密度為106lb/ft3（1698kd/m3） 的混泥土,其熱傳導率（k）在 21.1℃為0.38Btu（0.055W/mk）
  3.1.5*、二層由203mm厚的增強普通重量的水泥構成.頂部由能夠保證嚴密封性的墻面結構構成
  3.1.6位于第二層的測量孔必須在*層測量孔（305mm by 610mm）的垂直上方.每個孔離箱子后面203mm,離箱子側面102mm.
3.1 test chamber
3.1.1 u-shaped pressure gauge: measuring the pressure of the test chamber remain at 0-12 pa
3.1.2 temperature and humidity meter, measure the temperature and humidity test chamber
3.1.3 test chamber structure: overall structure by the concrete wall build by laying bricks or stones becomes, the first layer of 1.22 M, the second layer of 3.66 M, the top is 2.24 m. external size: 7.12 M high x1.3 M
Wide x2.5 M long.
3.1.4 wall structure is the density of 106 lb/ft3 (1698 kd/m3) of the concrete, the thermal conductivity (k) in 21.1 ℃ to 21.1 Btu (0.055 W/mk)
3.1.5 the first and second floor by 203 mm thick enhance the average weight of cement. The top is composed of can ensure strict sealing wall structure
3.1.6 is located in the second layer of hole must be in the first layer measurement hole (305 mm by 610 mm) above the vertical. Each hole 203 mm, from behind the box side is 102 mm away from the box.

：東莞中諾（中國臺灣）質檢儀器設備有限公司
Contact: dongguan (Taiwan) quality inspection instrument equipment co., LTD
                    （轉）815
                    （艾新華） 
                    http://www.ajh007.com
                    http://www.zon007.com
                    http://zonskyszajh.bmlink.com/
                    http://blog.sina.com.cn/u/3836926922