thermal shock test chamber – ts-72p
圖片僅供參考
temperature main features
溫度主要特征
★work trough temperature range: -40°c/+150°c
工作槽溫度范圍：-40°c/+150°c
★temperature resume time:≦5 minute
溫度恢復時間:≦5分鐘
★high temperature trough temperature range:60°c/+200°c
高溫槽溫度范圍：60°c/+200°c
★low temperature trough temperature range:-65°c/0°c
低溫槽溫度范圍：-65°c/0°c
★temperature variation rate: (nonlinear values with load and ambient temperature +10/+30°c):
溫度變化速率（+10/+30°c溫度下，不帶負載時的非線性值）：
heating from rt to +150°c: at 20minute
cooling from 0°c to -40°c: at 20 minute
升溫從rt到 +150°c 20分鐘內
降溫從0°c 到 -40°c 20分鐘內
★load:plating sanitation
負載： 空載
★ high and low temperature concussion invariablenes time:about 30minute
高低溫沖擊恒溫時間:約 30分鐘
★test method:
1. the temperature is according to gb/t 5170.2-1996 inspection methods.
2. the reference sensor is installed on blow-out of air conditioning unit.
dimensional main features
尺寸主要特征
★internal capacity: 72 liters
內部有效容積：72升
★internal dimensions: mm 450 x 400 x 400 (w x d x h)
內部有效尺寸：mm 450 x 400 x 400 (寬 x 深 x 高)
★ external dimensions: mm 1650 x 1730 x 1800 (w x d x h)
箱體外部尺寸：mm 1650 x 1730 x 1800 (寬 x 深 x 高)
cooling system
制冷系統
★cooling: the cooling part is the primary part of the cooling equipment , it supply all the quantity of cool which the equipment want to fall temperature and maintain . base on the differentia of test state, the cooling system will turn on, and offer cooling for the test course to attain the aim of equipment performance, . the equipment’s mechanical cooling used steam compress cooling . the basic theory cooling is as follows:
steam compress cooling is most economic and most broad cooling mode . it also the most usefulness in the climatic chamber equipments . it’s theory is the freon liquid vaporize from the cooled ob-ject and tak its heat out , as the drawing follow (vaporized and compress cooling circle course sketch map) . the liquid comed into the evaporator after throttle equipments . and vaporize after gained the latent quantity of heat . the gas after vaporize is low-cool and low-pressure . tis gas is inbreathed by the compressor . after compress , the high-tempreture and high-pressure gas came into the air condensator . after water condensator the refrigerants became high-pressure liquid . the high-pressure liquid came into the evaporator . such cycle repeated . the refrigerants absorb the quantity of heat , achieve cooling . than release the quantity of heat from the high ob-jects
售 后 服 務
中國售后服務中心： 宏瑞達科技（蘇州）有限公司
地址：江蘇省蘇州市吳中區浦莊大道浦莊工業園12號
1 安裝、調試
horad公司工程師可在買方準備好設備所需外部條件（如水、電等）后，負責該設備的安裝、調試、啟動工作，并提供良好的和售后服務，同時對使用人員進行設備現場培訓，保證受訓人員能夠獨立、熟練操作設備和完成簡單的維修工作、設備日常維護等工作。
2 保修
設備的保修期為一年，正式生效日期為買方在該設備的驗收合格書上簽字之日起計算。在保修期內，賣方負責該設備由于設備自身原因而引起的各種故障問題并負責無償解決。在保修期外，該設備的維修工作要收取備品備件的成本費用和一定的服務費用。
3 維修
維修反應時間為：24小時內響應
賣方在接到買方的故障通知后，保證在24小時內做出響應，并爭取在zui短的時間內盡快排除故障。
4 終身服務項目
賣方承諾在該設備的使用期間，可無償、無限期地提供該設備的工作。
